Lock Technology and Features

There are 4 features of a cylinder that can ensure nobody can enter your home through it without a key

1. Anti Pick - This is the process of using something small and thin to manipulate the pins inside the lock so they are all aligned enabling the lock to turn and thus open a door.

2. Anti Bump - This is a method of trying to move the pins by bumping them. A special/similar type of key is inserted into the lock, it’s then hit and the energy transferred into the key makes the pins jump upwards for a very small amount of time in which the key is turned at the same time and the door can be opened. This is preventented with smaller pin stacks so the pins in the cylinder cant jump as far and setting the pins at different heights on the sheer line.

3. Anti Drill - This is the method of drilling the lock through the sheer lie of a cylinder that completely destroys a log enableing anything that can fit inside to turn the cylinder. This is prevented by the use of hardened steel, anti drill pins and ceramic plates

4. Anti Snap - This is the process of snapping the lock in half in the centre exposing the internal components to turn the centre cam. Due to the nature of how a lock works and how its machined for the cam, it is a lot weaker in the centre. Modern locks are anti-snap which means the external part of the cylinder has a deliberate weak point between 10 and 20mm into the lock so when someone tries to snap the lock to gain entry, it snaps at the intended weak point leaving the mechanism and centre of the lock untouched. Should a cylinder get snapped, it can still be unlocked sing the correct key.

Which Lock is best?

There are loads of different cylinder brands. However, there are two locks that stand out to us from experience.

1. Avocet ABS
2. Ultion

Both locks are regarded in the industry as the very best. The Avocent ABS has a good proven track record for reliability, as well as maintaning all the security features, the Ultion lock is growing more and more popular and some would argue it is even more secure than an Avocet ABS. The Ultion lock has something called lockdown mode which locks the central cam in place if it detects the central cam is being tampered with. You can't go wrong with either lock, they are both great in terms of security and reliability and they cost roughly the same. 

Avocet

  • TS007 3 Star Approved

  • Sold Secure Diamond

  • Secured By Design

  • 6 Pins

  • Anti Snap - X2

Ultion

  • TS007 3 Star Approved

  • Sold Secure Diamond

  • Secured By Design

  • 11 Pins

  • Anti Snap - X2

  • Lockdown Mode

How to measure a lock in your door

Most locks on doors are very easy to take out and measure. On most UPVC and composite doors there will be a screw on the side of the door that screws into the cylinder.

With a tape measure, measure from the external side of the cylinder to the centre of the screw hole and do the same from the internal side of the cylinder.

You will end up with two numbers that may or may not be the same, i.e 45mm (internal) and 55mm (external), so this means your cylinder is 100mm in length but is offset, so you need to get a cylinder that is 45mm internal and 55m external. This is important as you need to make sure the cylinder goes back into the door correctly with the anti-snap on the external side.

It’s also worth noting that if your cylinder sticks out or is proud from the external handle, you can go for a smaller external sized cylinder, i.e if it sticks out 10mm from the external handle and the external size to the screw hole is 55mm, you can get a 45mm external cylinder and this will then sit a lot flusher with your handle.

How to change a lock?

1. On the side of your door, there will be a screw flush with your lock. Usually a Philips screw. Undo this and remove it completely. 
2. Insert your key into the lock. Turn your key to about 10 o’clock or about 2 o’clock and pull the cylinder out.

To put the lock back in, its just as easy,


1. Make sure the anti-snap side is external, some cylinders come with an anti-snap both sides, but the cylinder will say ‘EXT’ on it which means this is the external side.
2. Insert the key into the cylinder and turn the key so the black centre cam is flush within the cylinder, this will send slide right through your door. 
3. Get the cylinder central within the door and put the screw back in to secure your cylinder.